New Products

Cree XLamp™ MP-L EasyWhite LED - Unprecedented Performance!

 The XLamp MP-L EasyWhite LED offers the performance, color consistency and lumen density to displace conventional light sources, in a breakthrough 12 mm x 13 mm package design. Combining Cree EasyWhite technology with up to 1500 lumens of light at 250 mA this LED is the perfect choice for lighting applications where high luminous-flux output is required. Examples of specific applications include: commercial/retail display spotlights, LED retrofit bulbs, and other indoor and outdoor general-illumination applications.

Cree XLamp™ MX-6 LEDs - The New Standard for Indoor Lighting

 The XLamp MX-6 LED set the lighting-class standard for indoor LED lighting designs, with better color consistency and higher reliability than incumbent solutions. XLamp MX-6 LEDs deliver high lumen output with low forward voltage so there is no compromise between light output and efficacy.

LED Assembly Kit - Installation components for decorative illumination

 The "VS LED Assembly Kit" is designed to let you easily and safely create lighting solutions using state-of-the-art LED technology. The components contained in the kit are intended for use by luminaire manufacturers and enable numerous combinations of VS LED modules and VS ballasts. The VS LED Assembly Kit is IP20-protected. It is available in two lengths with two different attachments (transparent and milky white).

 The following VS LED assembly modules can be used with the VS LED Assembly Kit:
• LEDLine Flex HighBrightness
• LEDLine Flex SMD
• EasyLED

 You will find further information under category "Components for LED Lighting Technology"  -> "Accessories" on this website.

Energy-Efficient LED Street Lighting with Vossloh-Schwabe`s new 42 W LED driver

 Designed predominantly with street and general lighting applications in mind, Vossloh-Schwabe`s new 42 W LED driver can be used to operate up to 35 high-power LEDs at 350 mA. On top of that, the driver provides excellent protection against transient mains peaks of up to 4 kV and delivers an efficiency coefficient in excess of 4 kV, all of which go to make VS` new LED driver the ideal choice for operating energy-efficient lighting systems.

FiveLED Modules - High Brightness at Compact Size

 The new FiveLED modules from Vossloh-Schwabe are available in a brightness of up to 1.250 lm. FiveLED modules are assembled with five Cree XR-E LEDs. The used printed circuit board has a diameter of only 76 mm. Therefore it is suitable for numerous applications like the integration into luminaires, architectural lighting or for the use as ground luminaires. 

 FiveLED modules are available in white and warm white. They are driven by constant current. By using a plug-in contact an easy connection of the modules is possible. FiveLED modules can be equiped with 20mm Carclo optics. You will find further information on this website under category Products -> Cree -> Secondary Optics.

Setting the Scene with Vossloh-Schwabe

 Vossloh-Schwabe’s new HighPower-Mono system welcomes you to a previously uncharted galaxy of fresh design options for general lighting using LED. Guaranteeing a very high luminous flux and available in white, warm white, blue, green and red, the new LED modules are ideal for installation in luminaires. Great flexibility and 24V operation are further advantages of the HighPower-Mono system.

 Whatever your needs may be, Vossloh-Schwabe LED technology can help you to set the scene.

LED High Power Evolution: Complete VS RGB CA System

 RGB lighting with high-power LEDs has never been easier to design thanks to Vossloh-Schwabe´s new and complete 24V RGB high-power system. Combining high-power LEDs with the huge advantages of 24V systems produces complex and easily extendable system architectures. Diverse colour control options, high brightness and simple wiring enable a world of limitless RGB options.

Vossloh-Schwabe HighPower LED Modules – IP67 Model Now Available

 Vossloh-Schwabe’s TriplePowerEmitter IP67 is the first encapsulated HighPower module that is suitable for applications demanding IP67 protection. Engineered with highly efficient Cree XR-E LEDs, the TriplePowerEmitter is available in cool and warm white. As the brightest HighPower LEDs on the market, Cree LEDs have set a new standard in terms of versatility and luminosity.

 TriplePowerEmitter IP67 modules are available in a range of beam angles (15° to 90°) and are therefore ideal for just about any application. Vossloh-Schwabe’s TriplePowerEmitter IP67 modules not only include VS’s reliable HighPower thermal management, but also come with two fixing lugs for easy mounting using two M3 screws – all features that go to make this module unique. Pre-assembled leads additionally simplify the wiring process. The encapsulation method used for the module ensures unhindered heat discharge to the luminaire body. This makes the module ideal for installation in outdoor luminaires, architectural lighting, path markings as well as illuminated advertising.

Vossloh-Schwabe's DigiLED Mono CA new brightness control module

The best-in-class dimming device for mono-chromatic LED modules

 The cost-effective and easy to use dimming control module DigiLED Mono CA from Vossloh-Schwabe is the best-in-class device of its type available on the market to control monochromatic & white LED modules. DigiLED Mono CA can be used in combination with Vossloh-Schwabe´s LED modules of the 24V standard and 24V HighPower series.

 The output of 5A enables the dimming of a complete 10m roll of the monochromatic LEDLine Flex SMD modules with only one DigiLED Mono CA. Dimming control via 1-10V input or PWM interface. Due to its compact design (83x30x19 mm) it is especially suitable for integration into luminaires.

Vossloh-Schwabe`s new colour control module DigiLED RF gets a good reception!

 Using a wireless remote control to address Vossloh-Schwabe DigiLED RF units opens up new opportunities for LED installations. Now, systems featuring DigiLED RF and transmitters can be operated without having to ensure direct ‘line of sight’ between the individual units. This highly convenient remote device comes with a 7-key control pad.

 DigiLED RF units are designed to enable pre-programmed colour sequence control of LED modules. Whether you want to enable independent brightness con-trol of red, green and blue light, call up or store an indi-vidual colour value, run one of three pre-programmed colour sequences or adjust the speed of a colour se-quence, Vossloh-Schwabe’s DigiLED RF unit offers outstanding ease of use for your RGB applications.

Simply Better: High-Power 24 V RGB/CA System

 The new High-Power 24 V RGB/CA system enables modular and highly flexible LED systems. The new system responds to the trend towards market harmonisation and simplification of LED control technology. The modules require a 24 V DC operating voltage. Constant current control is effected via the circuit board and permits currents of up to 500 mA per LED. The modules are connected via an on-board push-in connector with matching connection cables.

 The RGB system is based on the common anode system, which enables mixed operation of high-power RGB modules and low-power modules that are designed according to the common anode principle. The high currents of high-performance LEDs used in the system result in brightness levels of up to 390 lm during RGB operation. Typical application areas for the High-Power 24 V RGB/CA system include:

• general lighting
• installation in luminaires
• architectural lighting
• lighting for art
• entertainment
• shop lighting

Extends Lighting-Class XLamp LED Performance with Multi-Chip Package

 The mulit-chip XLamp™ MC-E retains the same 7mm x 9mm footprint as Cree`s existing XLamp™ XR family LEDS while providing four times the light output of the existing XR-E, the highest lumen output for package of this size.

XLamp™ XP-E and XP-C - Cree is setting a new standard in general illumination with LED

 Cree announces a new standard for lighting-class LEDs with the introduction of the XLamp™ XP-E and XP-C LEDs. These breakthrough LEDs have the smallest footprint in the industry for lighting-class LEDs - providing the same high-quality lighting performance and proven reliability as Cree XR-E and XRC LEDs in an 80-percent smaller package. 

DigiLED Push - The compact and easy colour control

 The new DigiLED Push is a cost-effective and easy to use one button colour control module. It is the module of choise for simplified applications.

 DigiLED Push units are used to control pre-programmed colour sequences for the following Vossloh-Schwabe LED modules: LEDLine Flex RGB, EasyLED RGB, LEDLine 300/150 RGB and MarkerLED RGB. An externally connected push-button enables simple manual operation; e.g. start of colour sequences or choose of one colour.

Bright Lights for Display Cases: SpotLight 12V

 The SpotLight 12 V is now available. It is an optimised product for display case lighting and is specifically designed to provide a replacement for low-voltage white halogen luminaires.

 The integrated constant current control enables the operation at 12 V DC or magnetic 12 V AC voltage sources.

 Contacts are effected using two pins designed for use with GX5.3 lampholders. Typical applications include installation in luminaires, furniture lighting as well as shop and display case lighting.

EasyLED modules - Now available as RGB version

 Vossloh-Schwabe`s new EasyLED RGB modules are based upon the proven Chip-On-Board Technology. By positioning the 3 chips very close together under each glob-top achieves excellent colour mixing of the colours red, green and blue. 

 The modules are available in a lengths of 200mm with either 6 or 12 glob-tops. The 12 glob-top version can also be cut in half. Easy installation is facilitated by the new dedicated connection system "EasyConnect RGB".

Life in Full Colour: LEDLine RGB Push

 The LEDLine RGB Push is particularly suitable to be installed into furniture, as it provides simple colour effects. The LEDLine RGB Push module is an RGB module with an integrated on-board colour control unit that removes the need to use an external colour control module. The micro-controller stores a preprogrammed colour sequence.

 By connecting a conventional push-button, the colour sequence can be started and paused and its speed can be adjusted. The master circuit board can be connected to a maximum of two slaves which replicate the master colour sequence.

Four Times Brighter: LEDLine Flex High Brightness

 The product family of the well-known LEDLine Flex SMD modules has now been extended by a High Brightness model.
Equipped with LEDs with a power uptake of 0.5 W, this flexible module is available in white, warm white, red, green and blue. With a lumen output for White of up to 650 lm/m, it is five times as bright as the conventional version.

 With a maximum operating length of 5 m, this module is the longest on the market within its output class. The LEDLine Flex SMD High Brightness module can, for instance, be used for furniture and architectural as well as for entertainment and shop lighting.

VS-P3 – The LED solution for general lighting

 A revolutionary LED-technology for improved light quality with two narrow colour-bins and high colour rendering combined with superior heat dissipation was developed by Panasonic Electric Works Group. This technology is now available in compact VS-P3 modules which are available as Spotlight version with 4 LEDs (47 mm diameter) and Downlight version with 8 LEDs (59 mm diameter).

 Typical applications are general lighting applications like built-in luminaires as reading lights, desk lights and downlights. This series is also suitable in applications were a high colour rendering index is necessary like merchandise illumination, art illumination and colour inspection.

 The VS-P3 modules offers further optimised properties for LED lighting as:

• no binnings
• ultra long lifetime 40,000 h
• very high CRI: Ra ≈ 90
• very homogeneous light spot
• low energy consumption (8W/16W)
• highly efficient, high brightness
• compact design; new flat shape
• RoHS-compliant

New levels of light with VS LED Lighting Modules

 VS use the latest XR-E LEDs of the American producer Cree Inc. for its LED Lighting Modules. This makes it possible to attain outputs of up to 100 lm at 350 mA per LED.

 In addition, VS offers a narrow brightness and chromaticity location selection both for cool and warm white LED light. By using various drive options with VS constant current sources (350, 500, 700 and 1,050 mA) a huge range of options are now available for LED Lighting applications.

 VS modules are available in single, triple and linear configurations. The use of different integrated optical components completes the VS product portfolio.

LEDs - the flexible side of light

 The possibilities are endless with the LEDLine Flex SMD by Vossloh-Schwabe.
The RGB, warm white and white modules can be obtained in two brightness levels. The new generation is up to 70% brighter than the previous version. For outdoor use, there are also suitable modules available with protection class IP67.

 Variable pricing enables versatile applications for the widest variety of light projects: from general lighting and architectural lighting up to industrial lighting applications.

130W converter

 The LEDLine EDXe 1130/24 V is a converter with a voltage output of 24 V and a power output of up to 130 W to operate LED applications. This converter is electronically protected against overload, overheating and short-circuiting.

 With the high power output of 130 W Vossloh-Schwabe perfectly answers the trend for increased power requirements for LED modules in the illumination market.

HighPerformance Standard modules - availability of various colour temperatures

 Vossloh-Schwabe`s HighPerformance Standard modules are immediately available in the following colour temperatures:

• 3200K (warm white)
• 4200K and 5400K (neutral white)
• 6500K (cold white)

LEDLine High Power

 VS Optoelectronic extended its series of High Power modules with a line module. The LEDLine High Power is equipped with 12 Cree XLamp LEDs and is available in the colours blue, green, red, white and warm white.

  Due to an efficiency up to 52 lm/W the LEDLine High Power is especially suitable for the integration into luminaires. The possibility to attach different lenses enables customers to create several radiation angles.